sciencePeptideDosage

Peptide Calculator for Reconstitution and Syringe Units

This peptide reconstitution calculator turns vial size, bacteriostatic water and dose into exact U-100 syringe units, doses per vial and full supply planning. Pick a compound to auto-fill the vial and water, or enter your own values.

Loading calculator…

What this peptide calculator works out

A freeze-dried vial is labelled in milligrams of powder. A dose is written in micrograms or milligrams. The syringe in your hand is marked in units of volume. The calculator links the three: it divides the vial by the water to get a concentration in mg/mL, divides the dose by that concentration to get millilitres, and multiplies by 100 to get the mark on a U-100 insulin syringe, where one unit is 0.01 mL.

It then runs the supply side. From the frequency and the number of weeks you enter, it counts the injections in the block, the whole doses one vial gives, the vials you need (rounded up), and the water and syringes that go with them. For the plain conversion between mg, mL and units without a vial, use the mg to mL converter.

Same vial, same dose, different water

The water you add changes only the concentration. A 5 mg vial holds 5 mg whatever the volume, so a 250 mcg dose always gives 20 doses. What moves is the mark you draw to. Example figures only.

Water addedConcentration250 mcg doseU-100 unitsDoses in vial
1 mL5 mg/mL0.05 mL520
2 mL2.5 mg/mL0.1 mL1020
2.5 mL2 mg/mL0.125 mL12.520
3 mL1.667 mg/mL0.15 mL1520

At 1 mL the dose sits on the 5 unit mark, which is a short draw and easy to misjudge by a unit. At 2.5 mL it lands on 12.5 units. Neither is wrong; the second is simply easier to read.

Planning supplies for a research block

Take a 5 mg vial mixed with 2 mL, a 250 mcg dose, once a day for 8 weeks. That is 56 injections. Each vial gives 20 whole doses, so the block needs 56 ÷ 20 = 2.8 vials, rounded up to 3. Three vials at 2 mL each use 6 mL of bacteriostatic water, and one syringe per injection means 56 syringes. The calculator shows these totals as you change the inputs, so you can see how a different vial size or water volume changes the list.

Mixed vials have a limited in-use life, which depends on the product and how it is stored. Check the label or the supplier's documentation and plan the number of vials open at once around it. The reconstitution guide covers mixing and storage step by step.

Three slips the numbers will not catch

  • mcg typed as mg. 250 mcg is 0.25 mg. Entering 250 in the mg field gives an answer 1,000 times too large, which the over-capacity warning usually flags.
  • The wrong barrel selected. Units are the same on every U-100 syringe, but a 0.3 mL barrel stops at 30. Choose the barrel you will actually use.
  • A different water volume than you entered. If you added 3 mL but the calculator says 2 mL, every unit figure is off by a third. Enter what went into the vial.

For reading the barrel itself, see the insulin syringe guide.

Compound calculators

Each compound page runs the same calculator with that compound's common vial sizes loaded, next to its dosage notes.

Peptide calculator FAQ

What does the compound picker fill in?

It loads a vial size, a water volume and a starting dose for that compound so you have a set of numbers to begin from. Every field stays editable. Overwrite any of them with the figures on your own vial and protocol; the calculator does not know what your vial contains.

How much bacteriostatic water should I add?

The water volume is a choice, not a fixed rule. It sets the concentration, and the concentration decides how many units a dose takes. Pick a volume that puts your dose on marks you can read clearly, usually somewhere between 5 and 50 units, and that fits inside the syringe you own.

Why does the calculator round doses per vial down?

A vial that holds 20.6 doses gives you 20 full draws. The last fraction is not a usable dose, so supply planning counts whole doses only and treats the remainder as leftover.

How is the number of vials for a research block worked out?

Total doses for the block are frequency times weeks. That number is divided by whole doses per vial and rounded up, because you cannot buy part of a vial. Water and syringe totals follow from the vial count and the number of injections.

Can I use a 0.3 mL or 0.5 mL syringe instead of 1 mL?

Yes, as long as the dose fits. A 0.3 mL barrel holds 30 units and a 0.5 mL barrel holds 50 units on the U-100 scale. Smaller barrels have more space between marks, which makes small volumes easier to read. If the dose is larger than the barrel, the calculator warns you.

This calculator does arithmetic on the numbers you enter. It does not recommend doses and is not medical advice.